SHSB – 300 – HEAVY DUTY SINGLE PHASER

Related products

• 

  Quick view

  Read more

  TAKE UP RATIO

  TAKE-UP RATIO is the relation between the amount of medium paper and liner paper utilized by a single facer to produce corrugated board.

  THREE METHODS USED TO MEASURE THE T.U.R.

  1) Measuring feeding speed of paper.

  TUR = medium paper speed / liner paper speed

  2) Measuring the length of the corrugated board

  T.U.R. = Medium paper used to produce certain length of board/Liner paper used to produce the same length of board

  3) Using a Take Up Ratio Monitor

  The most accurate method of all, accurate to the third decimal point, i.e. 1.326 plus or minus 0.001 is the T.U.R. monitor.

  Quick view
• 

  Quick view

  Read more

  STACKER FOR N C CUT OFF MACHINE

  STACKER FOR N C CUT OFF MACHINE

  · STACKER SHALL BE INSTALLED AFTER N.C CUT OFF MACHINE.
  · STACKER IS PROVIDED WITH GEAR MOTOR AND VARIABLE SPEED DRIVE.
  · MULTIPLE ROLLER ARE FIXED ON THE STACKER WITH CONTINUED DRIVE.
  · ALL ROLLER ARE CONNECTED TO EACH OTHER WITH CHAIN GEAR DRIVE.
  · THE STACK HOLDER IS LIFTED AND LOWERED BY PNEUMATIC CYLINDER.
  · PANEL IS PROVIDED FOR MOVEMENT OF STACK AT 90 DEGREE
  · THIS CAN BE USED MANUALLY AND AT AUTO MODE.
  · STACK HOLDER ON MULTIPLE ROLLERS AT THE 90 DEGREE PLACED FOR ANY PICKUP AND MANUAL STACKING
  · ARE PRESSURE FOR PNEUMATIC CYLINDER 8 KG (AIR COMPRESSOR NOT IN OUR SCOPE).
  · MOTOR REQUIRED 03 HP 960 RPM

  Quick view
• 

  Quick view

  Read more

  DOUBLE PROFILE MODEL: SDR –320

  DOUBLE PROFILE MODEL: SDR –320.

  ONE SET OF TOOL BOX WITH TOOL SET.
  FLUTE ROLL:
  · 2 SET OF FLUTE ROLL BEARING.
  (ANY 2 SETS)
  · ROLL 320 MM DIA (EN-24 MATERIAL) HARD CHROME PLATED. HARDEN UPTO 50 HRC.
  · TOP ROLL 298 MM DIA (EN-24 MATERIAL) – HARD CHROME PLATED 50 HRC.
  · PRESSURE ROLL DIA 320 MM (EN-9 MATERIAL) GRINDED HARD CHROME PLATED.
  b) VACUUM JACKET FITTED ON THE PROFILES.
  c) 1 SET OF FLUTE ROLLER CAN BE USED AT ONE TIME.
  d) CHANGE THE FLUTE ROLL’S IN LESS THAN 3 MINUTES WITH HYDRAULIC POWER PACK.
  e) PRE- SHOWERS FOR STEAM ARRANGEMENT.
  f) REDUCTION GEAR BOX HEAVY DUTY
  g) THE UP AND DOWN OF UPPER CORRUGATING ROLL IS OPERATED MECHANICALLY. BY SCREW SYSTEM AND MANUAL LOCKING IS PROVIDED.
  h) COMPLETE ARRANGEMENT FOR GAS / ELECTRIC HEATING AS PER YOUR REQUIREMENT.
  i) THERE ARE ARRANGEMENTS PROVIDED IN CORRUGATION MACHINE TO SET THE TAPPER OF THE FLUTE IF THERE IS ANY.
  j) VACUUM SECTION BOX FITTED ON THE CENTRE FLUTE ROLLER (LATEST TYPE) FOR PAPER SUCTION INSTEAD OF ADOPTERS.
  k) BLOWER’ SHALL BE USED FOR SUCTION ALONG WITH 20 H. P. MOTOR.
  l) COMPLETE PIPE LINE WITH CLIPS SHALL BE PROVIDED ALONG WITH ALUMINIUM CASING FOR THE VACUUM BOX.
  m) VARIABLE SPEED DRIVE 15 H. P. DRIVES IS ALSO BE PROVIDED TOUCH SCREEN..
  n) GLUING ROLL AND DOCTOR ROLL HAVE BEEN ASSEMBLED PRECISE MICRO ADJUSTING DEVICE RESPECTIVELY FOR OBTAINING EXACT DISTANCE.
  j) PRE-HEATING ROLL DIAMETER 300MM X 1 PC. FOR BOTTOM PAPER.
  k) COMPLETE FRAME OF THE M/C IS FABRICATED FROM MILD STEAL TO ABSORB VIBRATION AND ACHIVE SPEED.
  l) ALL FLUTE ROLLER’S AND PRESSURE ROLLER’S ARE FIXED ON DOUBLE BEARING SYSTEM.
  EACH FLUTE ROLLER ARE FIXED ON 4 BEARING’S A- TOTAL OF 20 BEARING ARE FIXED FPR 2 SET’S OF FLUTE ROLLER AND ONE PRESSURE ROLLER.

  Quick view
• 

  Quick view

  Read more

  TRIPLEX PRE HEATER

  TRIPLEX PRE HEATER

  DIAMETER – 762 MM

  PRE HEATER ENHANCED HEAT CONDUCTION MOTORIZED WRAP ANGLE ADJUSTMENT RANGE 60 DEGREE – 220 DEGREE THREE SETS ARE FIXED ONE OVER THE OTHER 2 SETS ARE USED FOR 2 PLY LINER AND BOTTOM SET IS USED BOTTOM PAPER.

  THE WRAP AROUND SYSTEM HELP IN MAINTAINING PERFECT HEAT OF TO ALIVE PROPER PERFORMANCE (SPEED) AND BOUNDING OF BOARD CONTROL PANEL WITH REVERSE FORWARD STARTERS FIXED ON THE MACHINE PRE HEATER DRUM AND SHEET GRINDING ROLLS ARE HARDCROME. IT’S WORKING PRESSURE IS 1.1 – 1.2 MPA. METAL SORT PIPE (SYPHONE) ARE NEEDED TO BE FIXED FOR PERFECT DRAIN.

  Quick view